- Interlocking Devices: The Good, The Bad and the Ugly
- Presence Sensing Devices – Reaching over sensing fields
- Trapped Key Interlocking
- ISO 13857 – Safety Distances”>Canada Adopts ISO 13857 – Safety Distances
- How to Apply a Safety Edge to a Machine Guard – Part 1: Pressure-sensitive devices
- How to Apply a Safety Edge to a Machine Guard – Part 2: Design Considerations
- How to Apply a Safety Edge to a Machine Guard – Part 3: Stopping Performance
Note: A shorter version of this article was published in the May-2012 edition of Manufacturing Automation Magazine.
When designing safeguarding systems for machines, one of the basic building blocks is the movable guard. Movable guards can be doors, panels, gates or other physical barriers that can be opened without using tools. Every one of these guards needs to be interlocked with the machine control system so that the hazards covered by the guards will be effectively controlled when the guard is opened.
There are a number of important aspects to the design of movable guards. This article will focus on the selection of interlocking devices that are used with movable guards.
The Hierarchy of Controls
This article assumes that a risk assessment has been done as part of the design process. If you haven’t done a risk assessment first, start there, and then come back to this point in the process. You can find more information on risk assessment methods in this post from 31-Jan-11. ISO 12100  can also be used for guidance in this area.
The hierarchy of controls describes levels of controls that a machine designer can use to control the assessed risks. The hierarchy is defined in . Designers are required to apply every level of the hierarchy in order, starting at the top. Each level is applied until the available measures are exhausted, or cannot be applied without destroying the purpose of the machine, allowing the designer to move to the next lower level.
Engineering controls are subdivided into a number of different sub-groups. Only movable guards are required to have interlocks. There are a number of similar types of guards that can be mistaken for movable guards, so let’s take a minute to look at a few important definitions.
Table 1 – Definitions
|International ||Canadian ||USA |
|3.27 guard physical barrier, designed as part of the machine to provide protection.NOTE 1 A guard may act either alone, in which case it is only effective when “closed” (for a movable guard) or “securely held in place” (for a fixed guard), or in conjunction with an interlocking device with or without guard locking, in which case protection is ensured whatever the position of the guard.NOTE 2Depending on its construction, a guard may be described as, for example, casing, shield, cover, screen, door, enclosing guard.NOTE 3 The terms for types of guards are defined in 3.27.1 to 3.27.6. See also 22.214.171.124 and ISO 14120 for types of guards and their requirements.||Guard — a part of machinery specifically used to provide protection by means of a physical barrier. Depending on its construction, a guard may be called a casing, screen, door, enclosing guard, etc.||3.22 guard: A barrier that prevents exposure to an identified hazard.E3.22 Sometimes referred to as “barrier guard.”|
|3.27.4 interlocking guard guard associated with an interlocking device so that, together with the control system of the machine, the following functions are performed:
NOTE ISO 14119 gives detailed provisions.
|Interlocked barrier guard — a fixed or movable guard attached and interlocked in such a manner that the machine tool will not cycle or will not continue to cycle unless the guard itself or its hinged or movable section encloses the hazardous area.||3.32 interlocked barrier guard: A barrier, or section of a barrier, interfaced with the machine control system in such a manner as to prevent inadvertent access to the hazard.|
|3.27.2 movable guard
guard which can be opened without the use of tools
|Movable guard — a guard generally connected by mechanical means (e.g., hinges or slides) to the machine frame or an adjacent fixed element and that can be opened without the use of tools. The opening and closing of this type of guard may be powered.||3.37 movable barrier device: A safeguarding device arranged to enclose the hazard area before machine motion can be initiated.E3.37 There are two types of movable barrier devices:
|3.28.1 interlocking device (interlock)mechanical, electrical or other type of device, the purpose of which is to prevent the operation of hazardous machine functions under specified conditions (generally as long as a guard is not closed)||Interlocking device (interlock) — a mechanical, electrical, or other type of device, the purpose of which is to prevent the operation of machine elements under specified conditions (usually when the guard is not closed).||No definition|
|3.27.5 interlocking guard with guard locking guard associated with an interlocking device and a guard locking device so that, together with the control system of the machine, the following functions are performed:
NOTE ISO 14119 gives detailed provisions.
|Guard locking device — a device that is designed to hold the guard closed and locked until the hazard has ceased.||No definition|
As you can see from the definitions, movable guards can be opened without the use of tools, and are generally fixed to the machine along one edge. Movable guards are always associated with an interlocking device. Guard selection is covered very well in ISO 14120 . This standard contains a flowchart that is invaluable for selecting the appropriate style of guard for a given application.
Though much emphasis is placed on the correct selection of these interlocking devices, they represent a very small portion of the hierarchy. It is their widespread use that makes them so important when it comes to safety system design.
Electrical vs. Mechanical Interlocks
Most modern machines use electrical interlocks because the machine is fitted with an electrical control system, but it is entirely possible to interlock the power to the prime movers using mechanical means. This doesn’t affect the portion of the hierarchy involved, but it may affect the control reliability analysis that you need to do.
Figure 2, from ISO 14119 [7, Fig. H.1, H.2 ], shows one example of a mechanical interlock. In this case, when cam 2 is rotated into the position shown in a), the guard cannot be opened. Once the hazardous condition behind the guard is effectively controlled, cam 2 rotates to the position in b), and the guard can be opened.
Arrangements that use the open guard to physically block operation of the controls can also be used in this way. See Figure 3 [7, Fig. C.1, C.2].
Fluid Power Interlocks
Figure 4, from [7, Fig. K.2], shows an example of two fluid-power valves used in complementary mode on a single sliding gate.
In this example, fluid can flow from the pressure supply (the circle with the dot in it at the bottom of the diagram) through the two valves to the prime-mover, which could be a cylinder, or a motor or some other device when the guard is closed (position ‘a’). There could be an additional control valve following the interlock that would provide the normal control mode for the device.
When the guard is opened (position ‘b’), the two valve spools shift to the second position, the lower valve blocks the pressure supply, and the upper valve vents the pressure in the circuit, helping to prevent unexpected motion from trapped energy.
If the spring in the upper valve fails, the lower spool will be driven by the gate into a position that will still block the pressure supply and vent the trapped energy in the circuit.
By far the majority of interlocks used on machinery are electrical. Electrical interlocks offer ease of installation, flexibility in selection of interlocking devices, and complexity from simple to extremely complex. The architectural categories cover any technology, whether it is mechanical, fluidic, or electrical, so let’s have a look at architectures first.
In Canada, CSA Z432  and CSA Z434  provide four categories of control reliability: simple, single channel, single-channel monitored and control reliable. In the U.S., the categories are very similar, with some differences in the definition for control reliable (see RIA R15.06, 1999). In the EU, there are five levels of control reliability, defined as Performance Levels (PL) given in ISO 13849 – 1 : PL a, b, c, d and e. Underpinning these levels are five architectural categories: B, 1, 2, 3 and 4. Figure 5 shows how these architectures line up.
To add to the confusion, IEC 62061  is another international control reliability standard that could be used. This standard defines reliability in terms of Safety Integrity Levels (SILs). These SILs do not line up exactly with the PLs in , but they are similar.  is based on IEC 61508 , a well-respected control reliability standard used in the process industries.  is not well suited to applications involving hydraulic or pneumatic elements.
The orange arrow in Figure 5 highlights the fact that the definition in the CSA standards results in a more reliable system than the ANSI/RIA definition because the CSA definition requires TWO (2) separate physical switches on the guard to meet the requirement, while the ANSI/RIA definition only requires redundant circuits, but makes no requirement for redundant devices. Note that the arrow representing the ANSI/RIA Control reliability category falls below the ISO Category 3 arrow due to this same detail in the definition.
Note that Figure 5 does not address the question of PL’s or SIL’s and how they relate to each other. That is a topic for another article!
The North American architectures deal primarily with electrical or fluid-power controls, while the EU system can accommodate electrical, fluid-power and mechanical systems.
From the single-channel-monitored or Category 2 level up, the systems are required to have testing built-in, enabling the detection of failures in the system. The level of fault tolerance increases as the category increases.
Interlocking devices are the components that are used to create the interlock between the safeguarding device and the machine’s power and control systems. Interlocking systems can be purely mechanical, purely electrical or a combination of these.
Most machinery has an electrical/electronic control system, and these systems are the most common way that machine hazards are controlled. Switches and sensors connected to these systems are the most common types of interlocking devices.
Interlocking devices can be something as simple as a micro-switch or a reed switch, or as complex as a non-contact sensor with an electromagnetic locking device.
Images of interlocking devices used in this article are representative of some of the types and manufacturers available, but should not be taken as an endorsement of any particular make or type of device. There are lots of manufacturers and unique models that can fit any given application, and most manufacturers have similar devices available.
Photo 1 shows a safety-rated, direct-drive roller cam switch used as half of a complementary switch arrangement on a gate interlock. The integrator failed to cover the switches to prevent intentional defeat in this application.
Photo 2 shows a ‘microswitch’ used for interlocking a machine cover panel that is normally held in place with fasteners, and so is a ‘fixed guard’ as long as the fasteners require a tool to remove. Fixed guards do not require interlocks under most circumstances. Some product family standards do require interlocks on fixed guards due to the nature of the hazards involved.
Microswitches are not safety-rated and are not recommended for use in this application. They are easily defeated and tend to fail to danger in my experience.
Requirements for interlocking devices are published in a number of standards, but the key ones for industrial machinery are ISO 14119 , , and ANSI B11.0 . These standards define the electrical and mechanical requirements, and in some cases the testing requirements, that devices intended for safety applications must meet before they can be classified as safety components.
These devices are also integral to the reliability of the control systems into which they are integrated. Interlock devices, on their own, cannot meet a reliability rating above ISO 13849 – 1 Category 1, or CSA Z432-04 Single Channel. To understand this, consider that the definitions for Category 2, 3 and 4 all require the ability for the system to monitor and detect failures, and in Categories 3 & 4, to prevent the loss of the safety function. Similar requirements exist in CSA and ANSI’s “single-channel-monitored,” and “control-reliable” categories. Unless the interlock device has a monitoring system integrated into the device, these categories cannot be achieved.
Interlocking devices are often used in conjunction with guard locking. There are a few reasons why a designer might want to lock a guard closed, but the most common one is a lack of safety distance. In some cases the guard may be locked closed to protect the process rather than the operator, or for other reasons.
Safety distance is the distance between the opening covered by the movable guard and the hazard. The minimum distance is determined using the safety distance calculations given in  and ISO 13855 . This calculation uses a ‘hand-speed constant’, called K, to represent the theoretical speed that the average person can achieve when extending their hand straight forward when standing in front of the opening. In North America, K is usually 63 inches/second, or 1600 mm/s. Internationally and in the EU, there are two speeds, 2000 mm/s, used for an approach perpendicular to the plane of the guard, or 1600 mm/second for approaches at 45 degrees or less . 2000 mm/s is used with movable guards, and is approximately equivalent to 79 inches/second. Using the International approach, if the value of Ds is greater than 500 mm when calculated using K = 2 000, then  permits the calculation to be done using K = 1 600 instead.
Using the stopping time of the machinery and K, the minimum safety distance can be calculated.
Eq. 1 Ds = K x Ts
Using Equation 1 , assume you have a machine that takes 250 ms to stop when the interlock is opened. Inserting the values into the equation gives you a minimum safety distance of:
Example 1 Ds = 63 in/s x 0.250 s = 15.75 inches
Example 2 Ds = 2000 mm/s x 0.250 s = 500 mm
As you can see, the International value of K gives a more conservative value, since 500 mm is approximately 20 inches.
Note that I have not included the ‘Penetration Factor’, Dpf in this calculation. This factor is used with presence sensing safeguarding devices like light curtains, fences, mats, two-hand controls, etc. This factor is not applicable to movable, interlocked guards.
Also important to consider is the amount the guard can be opened before activating the interlock. This will depend on many factors, but for simplicity, consider a hinged gate on an access point. If the guard uses two hinge-pin style switches, you may be able to open the gate a few inches before the switches rotate enough to detect the opening of the guard. In order to determine the opening size, you would slowly open the gate just to the point where the interlock is tripped, and then measure the width of the opening. Using the tables found in , , , or ISO 13857 , you can then determine how far the guard must be from the hazards behind it. If that distance is greater than what is available, you could remove one hinge-pin switch, and replace it with another type mounted on the post opposite the hinges. This could be a keyed interlock like Photo 3, or a non-contact device like Photo 5. This would reduce the opening width at the point of detection, and thereby reduce the safety distance behind the guard. But what if that is still not good enough?
If you have to install the guard closer to the hazard than the minimum safety distance, locking the guard closed and monitoring the stand-still of the machine allows you to ignore the safety distance requirement because the guard cannot be opened until the machinery is at a standstill, or in a safe state.
Guard locking devices can be mechanical, electromagnetic, or any other type that prevents the guard from opening. The guard locking device is only released when the machine has been made safe.
There are many types of safety-rated stand-still monitoring devices available now, and many variable-frequency drives and servo drive systems are available with safety-rated stand-still monitoring.
Environment, failure modes and fault exclusion
Every device has failure modes. The correct selection of the device starts with understanding the physical environment to which the device will be exposed. This means understanding the temperature, humidity, dust/abrasives exposure, chemical exposures, and mechanical shock and vibration exposures in the application. Selecting a delicate reed switch for use in a high-vibration, high-shock environment is a recipe for failure, just as selecting a mechanical switch in a dusty, damp, corrosive environment will also lead to premature failure.
Interlock device manufacturers have a variety of non-contact interlocking devices available today that use coded RF signals or RF ID technologies to ensure that the interlock cannot be defeated by simple measures, like taping a magnet to a reed switch. The Jokab EDEN system is one example of a system like this that also exhibits IP65 level resistance to moisture and dust. Note that systems like this include a safety monitoring device and the system as a whole can meet Control Reliable or Category 3 / 4 architectural requirements when a simple interlock switch could not.
The device standards do provide some guidance in making these selections, but it’s pretty general.
Fault exclusion is another key concept that needs to be understood. Fault exclusion holds that failure modes that have an exceedingly low probability of occurring during the lifetime of the product can be excluded from consideration. This can apply to electrical or mechanical failures. Here’s the catch: Fault exclusion is not permitted under any North American standards at the moment. Designs based on the North American control reliability standards cannot take advantage of fault exclusions. Designs based on the International and EU standards can use fault exclusion, but be aware that significant documentation supporting the exclusion of each fault is needed.
The North American standards require that the devices chosen for safety-related interlocks be defeat-resistant, meaning they cannot be easily fooled with a cable-tie, a scrap of metal or a piece of tape.
Figure 6 [7, Fig. 10] shows a key-operated switch, like the Schmersal AZ15, installed with a cover that is intended to further guard against defeat. The key, sometimes called a ‘tongue’, used with the switch prevents defeat using a flat piece of metal or a knife blade. The cover prevents direct access to the interlocking device itself. Use of tamper-resistant hardware will further reduce the likelihood that someone can remove the key and insert it into the switch, bypassing the guard.
The International and EU standards do not require the devices to be inherently defeat resistant, which means that you can use “safety-rated” limit switches with roller-cam actuators, for example. However, as a designer, you are required to consider all reasonably foreseeable failure modes, and that includes intentional defeat. If the interlocking devices are easily accessible, then you must select defeat-resistant devices and install them with tamper-resistant hardware to cover these failure modes.
Photo 6 shows one type of tamper resistant fasteners made by Inner-Tite . Photo 7 shows fasteners with uniquely keyed key ways made by Bryce Fastener , and Photo 8 shows more traditional tamperproof fasteners from the Tamperproof Screw Company . Using fasteners like these will result in the highest level of security in a threaded fastener. There are many different designs available from a wide variety of manufacturers.
Almost any interlocking device can be bypassed by a knowledgeable person using wire and the right tools. This type of defeat is not generally considered, as the degree of knowledge required is greater than that possessed by “normal” users.
How to select the right device
When selecting an interlocking device, start by looking at the environment in which the device will be located. Is it dry? Is it wet (i.e., with cutting fluid, oil, water, etc.)? Is it abrasive (dusty, sandy, chips, etc.)? Is it indoors or outdoors and subject to wide temperature variations?
Is there a product standard that defines the type of interlock you are designing? An example of this is the interlock types in ANSI B151.1  for plastic injection moulding machines. There may be restrictions on the type of devices that are suitable based on the requirements in the standard.
Consider integration requirements with the controls. Is the interlock purely mechanical? Is it integrated with the electrical system? Do you require guard locking capability? Do you require defeat resistance? What about device monitoring or annunciation?
Once you can answer these questions, you will have narrowed down your selections considerably. The final question is: What brand is preferred? Go to your preferred supplier’s catalogues and make a selection that fits with the answers to the previous questions.
The next stage is to integrate the device(s) into the controls, using whichever control reliability standard you need to meet. That is the subject for a series of articles!
 Safety of machinery – General principles for design – Risk assessment and risk reduction, ISO Standard 12100, Edition 1, 2010
 Safeguarding of Machinery, CSA Standard Z432, 2004 (R2009)
 Industrial Robots and Robot Systems – General Safety Requirements, CSA Standard Z434, 2003 (R2008)
 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design, ISO Standard 13849 – 1, 2006
 Safety of machinery – Functional safety of safety-related electrical, electronic and programmable electronic control systems, IEC Standard 62061, Edition 1, 2005
 Functional safety of electrical/electronic/programmable electronic safety-related systems (Seven Parts), IEC Standard 61508‑X
 Safety of machinery – Interlocking devices associated with guards – Principles for design and selection, ISO Standard 14119, 1998
 American National Standard for Machines, General Safety Requirements Common to ANSI B11 Machines, ANSI Standard B11, 2008
Download ANSI standards
 Safety of machinery — Positioning of safeguards with respect to the approach speeds of parts of the human body, ISO 13855, 2010
 American National Standard for Machine Tools – Performance Criteria for Safeguarding, ANSI B11.19, 2003
 Safety of machinery — Guards — General requirements for the design and construction of fixed and movable guards, ISO 14120. 2002
 Safety of machinery – Safety distances to prevent hazard zones being reached by upper and lower limbs, ISO 13857. 2008.
 Inner-Tite Corp. home page. (2012). Available: http://www.inner-tite.com/
 Bryce Fastener, Inc. home page. (2012). Available: http://www.brycefastener.com/
 Tamperproof Screw Co., Inc., home page. (2013). Available: http://www.tamperproof.com