Machinery Safety 101

ISO 13849 – 1 Analysis — Part 7: Safety-Related Software

General architecture model of software
This entry is part 7 of 9 in the series How to do a 13849 – 1 ana­lys­is

Post updated 2019-07-24. Ed. Safety-Related Soft­ware Up to this point, I have been dis­cuss­ing the basic pro­cesses used for the design of safety-related parts of con­trol sys­tems. The under­ly­ing assump­tion is that these tech­niques apply to the design of hard­ware used for safety pur­poses. The remain­ing ques­tion focuses on the design and devel­op­ment of safety-related soft­ware…

Read More

An update on CE Marking Electrical Cable

CE Mark­ing Wire and Cable In an earli­er post, I wrote about the require­ments for CE Mark­ing wire and cable and dis­cussed the <HAR> mark. In 2016, the Con­struc­tion Products Reg­u­la­tion 305/2011 (CPR) came into effect, repla­cing the Con­struc­tion Products Dir­ect­ive 89/106/EEC. The CPR included pro­vi­sions cov­er­ing any kind of mater­i­als that could be used in…

Read More

ISO 13849 – 1 Analysis — Part 6: CCF — Common Cause Failures

This entry is part 6 of 9 in the series How to do a 13849 – 1 ana­lys­is

Post updated 2019-07-24. Ed. What is a “Com­mon Cause Fail­ure”? There are two sim­il­ar-sound­ing terms that people often get con­fused: Com­mon Cause Fail­ure (CCF) and Com­mon Mode Fail­ure. While these two types of fail­ures sound sim­il­ar, they are dif­fer­ent. A Com­mon Cause Fail­ure is a fail­ure in a sys­tem where two or more por­tions of the sys­tem fail at…

Read More

ISO 13849 – 1 Analysis — Part 5: Diagnostic Coverage (DC)

A graph showing the theoretical "bathtub curve" for product failure rate over the lifetime of the product.
This entry is part 5 of 9 in the series How to do a 13849 – 1 ana­lys­is

Post updated 2019-07-24. Ed. What is Dia­gnost­ic Cov­er­age? Under­stand­ing Dia­gnost­ic Cov­er­age (DC) as it is used in ISO 13849 – 1 [1] is crit­ic­al to ana­lys­ing the design of any safety func­tion assessed using this stand­ard. In case you missed a pre­vi­ous part of the series, you can read it here. In the last instal­ment of this series dis­cuss­ing…

Read More

ISO 13849 – 1 Analysis — Part 4: MTTFD – Mean Time to Dangerous Failure

This entry is part 4 of 9 in the series How to do a 13849 – 1 ana­lys­is

Post updated 2019-07-24. Ed. Func­tion­al safety is all about the like­li­hood of a safety sys­tem fail­ing to oper­ate when you need it. Under­stand­ing Mean Time to Dan­ger­ous Fail­ure, or MTTFD, is crit­ic­al. If you have been read­ing about this top­ic at all, you may notice that I am abbre­vi­at­ing Mean Time to Dan­ger­ous Fail­ure with all cap­it­al…

Read More

ISO 13849 – 1 Analysis — Part 3: Architectural Category Selection

This entry is part 3 of 9 in the series How to do a 13849 – 1 ana­lys­is

Post updated 2019-07-24. Ed. At this point, you have com­pleted the risk assess­ment, assigned required Per­form­ance Levels to each safety func­tion, and developed the Safety Require­ment Spe­cific­a­tion for each safety func­tion. Next, you need to con­sider three aspects of the sys­tem design: Archi­tec­tur­al Cat­egory, Chan­nel Mean Time to Dan­ger­ous Fail­ure (MTTFD), and Dia­gnost­ic Cov­er­age (DCavg). In…

Read More

ISO 13849 – 1 Analysis — Part 2: Safety Requirement Specification

This entry is part 2 of 9 in the series How to do a 13849 – 1 ana­lys­is

This art­icle was updated 2019-07-24. Ed. Devel­op­ing the Safety Require­ment Spe­cific­a­tion The Safety Require­ment Spe­cific­a­tion sounds pretty heavy, but actu­ally, it is just a big name for a way to organ­ize the inform­a­tion you need to have to ana­lyze and design the safety sys­tems for your machinery. Note that I am assum­ing that you are doing this in…

Read More

Brexit Update – CE Marking and the UK

Brexit: UK and EU Flags against a blue sky

I recently read a press release by UKAS, the UK’s accred­it­a­tion body, regard­ing their ongo­ing dis­cus­sions with the UK gov­ern­ment regard­ing the impact that BREXIT could have on UK accred­it­a­tion. As men­tioned by Douglas Florence in a recent dis­cus­sion on Linked­In, it’s pos­sible that if not handled well things could end up in a bit of a mess. Mr…

Read More

ISO 13849 – 1 Analysis — Part 1: Start with Risk Assessment

This entry is part 1 of 9 in the series How to do a 13849 – 1 ana­lys­is

This post was updated 2019-07-24 I often get ques­tions from cli­ents about how to get star­ted on Func­tion­al Safety using ISO 13849. This art­icle is the first in a series that will walk you through the basics of using ISO 13849. Keep in mind that you will need to hold a copy of the 3rd edi­tion of ISO 13849 – 1 [1]…

Read More

The Brexit Vote and CE Marking: What’s it going to mean for Canadian Exporters?

Shocked and Amazed by Brexit This morn­ing I am shocked and amazed to learn that one of the founders of the European Uni­on has chosen to leave that Uni­on. Join­ing the EEC in 1973, the UK and oth­er European coun­tries moved toward the form­a­tion of the EU, first as an eco­nom­ic treaty, and even­tu­ally as a polit­ic­al…

Read More
All original content on these pages is fingerprinted and certified by Digiprove